Sika | SKU: 644609

SikaTile 300 Set - 50 Lb. Non Modified Thinset Mortar - Pallet

$408⁰⁰

Shipping calculated at checkout.

Colors

Gray - (48 Bags) White - (48 Bags)

Product variants

Safe & Secure Payments.

Note: Hazardous chemicals must be shipped via UPS Ground. All other shipping options will be removed from checkout if added to cart. If you need expedited services for non-hazardous products, please make a separate transaction.

SikaTile 300 Set - 50 Lb. Gray Non-Modified Mortar 48 Piece Pallet

SikaTile - 300 Set is a non-modified, dry-set mortar for use in interior and exterior residential and light commercial floor and wall applications.

Features

48 Bags per pallet
Can be used over plywood substrates when mixed with Sika Latex R
For interior and exterior floors and walls
Allow 24-48 hours before grouting and light traffic, and 7 days before heavy or vehicular traffic
SikaTile - 300 Set is suitable for bonding brick, ceramic, mosaic, quarry, cement body tile, vitreous, semi-vitreous or non-vitreous tile, natural stone tile, cement-based precast terrazzo, impervious porcelain and glass tile
Mold and mildew resistant
Mixing Ratio: 5 quarts (4.75 liters) of clean potable water per bag

Suitable Substrates

Ceramic Tile and Stone
Cement Backer Board
Cement Mortar Beds (cured)
Cement Plaster
Cement Terrazzo
Concrete
Exterior Grade Plywood (interior use only)
Concrete Masonry
Lightweight Gypsum Concrete (interior use only)
SikaLevel Products

Advantages

For use with ceramic tile and dimensionally stable natural stone
Can be used over plywood substrates when mixed with Sika Latex R
For interior and exterior floors and walls
No-Slake - No wait. Just mix, trowel, and install
Mold and mildew resistant

Usage

SikaTile®-300 Set is suitable for bonding the following types of tile and stone:

Brick and thin brick
Cement-based precast terrazzo
Impervious porcelain and glass tile
Natural stone tile
Vitreous, semi-vitreous or non-vitreous tile:
- Ceramic, mosaic, quarry, cement body tile

SikaTile®-300 Set can be installed in most interior and exterior residential and commercial installations on floors and walls on the following recommended substrates when mixed with water:

Brick Masonry
Cement Backer Board¹
Cement Mortar Beds
Cement Plaster
Cement Terrazzo
Concrete
Concrete Masonry
Gypsum Wallboard²
SikaLevel®
SikaTile® Membranes
Approved SikaLastic® Under Tile Waterproofing

¹ Consult cement backer board manufacturer for installation recommendations and to verify acceptability for exterior use.
² Interior Use Only. When mixed with Sika® Latex R, SikaTile®-300 Set can be installed in most interior and exterior residential and commercial installations on floors and walls on the following recommended substrates:

Brick Masonry
Cement Backer Board¹
Cement Mortar Beds
Cement Plaster
Cement Terrazzo
Ceramic Tile and Stone
Concrete
Concrete Masonry
Cutback Adhesive
Exterior Grader Plywood²
Gypsum Wallboard²
SikaLevel®
SikaTile® Membranes
Approved SikaLastic® Under Tile Waterproofing

¹ Consult cement backer board manufacturer for installation recommendations and to verify acceptability for exterior use.
² Interior Use Only.

Advantages

For use with ceramic tile and dimensionally stable natural stone
Can be used over plywood substrates when mixed with Sika Latex R
For interior and exterior floors and walls
No-Slake - No wait. Just mix, trowel, and install
Mold and mildew resistant

Packaging

50 lb. (22.68 kg.) bag

ENVIRONMENTAL INFORMATION

Sika® is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product can contribute towards LEED® v4.1 certification:

Up to 2 points towards MR Credit 5, Regional Materials
Up to 1 point towards IEQ Credit 4.1, Low-Emitting Materials – Adhesives & Sealants

APPROVALS / STANDARDS

American National Standards Institute (ANSI) — ANSI A108.5, A118.1 (A118.4 and A118.11 when mixed with Sika® Latex R) of the American National Standards for the Installation of Ceramic Tile ASTM International (ASTM)

ASTM C109 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2” or 50mm Cube Specimens)
Resilient Floor Covering Institute - (RFCI) Recommended Work Practices for Removal of Resilient Floor Coverings
Tile Council of North America (TCNA) - TCNA Handbook for Ceramic Tile Installation, TCNA EJ171 Movement Joint Guidelines.
ISO 13007-2

Chemical Base

Portland cement, selected aggregates, water retention additives

Shelf Life

15 months from date of production when stored in original, sealed package

Storage Conditions

Store in undamaged, original, sealed package, in dry conditions at 73⁰ F (23⁰ C)

Mixing Ratio

5 quarts (4.75 liters) of clean potable water per bag

Pot Life

> 60 minutes

Open Time

> 20 minutes - Passes ANSI A118.1 Section 5.3

Cure Time

Product Curing time is affected by ambient and surface temperatures and humidity. Use the following as a guideline. Allow 24-48 hours before grouting and light traffic, and 7 days before heavy or vehicular traffic. As necessary, use plywood or other load distributing protection when moving heavy equipment across tiled assembly.

Application steps

MIXING

In a clean container, add approximately 5 quarts (4.75 liters) of clean potable water. Then add the contents of the 50 lb. (22.67 kg) SikaTile®-300 Set Mortar. For mortar meeting A118.4 or A118.11 requirements, use 5 quarts (4.75 L) of Sika® Latex R admixture in place of water. Mix thoroughly by hand or with a slow speed mixer to a smooth, thick, trowelable consistency. Mortar consistency shall be such that when applied with the recommended notched trowel to the substrate, the ridges formed in the mortar do not flow or slump. During use, stir mortar mix occasionally. Do not add additional water. Do not add latex liquid additives to SikaTile®-300 Set Mortar.

APPLICATION

Read all installation instructions before installation. Choose a notched trowel with sufficient depth to achieve more than 80% mortar contact to both the tile and substrate for all interior applications, and more than 95% for exterior, commercial floor and wet applications. It may be necessary to back-butter the tile to meet these requirements. With pressure, apply a coat of mortar by using the flat side of the trowel to key the mortar into the substrate. With the notched side of the trowel, apply additional mortar by combing it in a single direction parallel to the shortest dimension of the tile. Spread only as much mortar as can be tiled before the product skins over. Open time can vary with jobsite conditions. Set tiles firmly into the wet mortar and push the tiles back and forth in a direction perpendicular to trowel lines to collapse the mortar ridges and to help achieve maximum coverage.