Poxi-Rock Flooring
SKU: 14850
Poxi-Rock Flooring
- 1 Gallon (1 Batch Kit)
- 3 Gallon Unit (four 3/4-gallon BAG-PAKsTMin 1 pail)
- 4.5 Gallon Unit (six 3/4-gallon BAG-PAKsTMin 1 pail)
- 25 Gallon Unit in Five 5-gallon pails
- VOC compliant and low odor
- Compressive strength of 11,000+ PSI at ¼" mortar thickness
- Non-shrink product for patching and grouting
- Fast Curing
- Can be power or hand troweled
- Can be grouted and sealed with other ROCK-TRED coatings, or left unsealed
Description
POXI-ROCK FLOORING is a 2 component, 98% solids epoxy binder resin to be blended with ROCK-TRED aggregates to create a trowel grade mortar. POXI-ROCK FLOORING meets USDA/FDA guidelines for use in federally inspected facilities.
Uses
POXI-ROCK FLOORING is used to create resurfacing epoxy mortar overlays, for repairing non-moving joints, cracks and spalls in concrete floors and for installing hand formed cove base, ramping and slopes in floors. It is formulated for easy hand or power trowel applications.
Typical Coverage
POXI-ROCK FLOORING will cover approximately 25 sq. ft. at a ¼ inch thickness when 0.75 mixed gallons of liquids are combined with 50 lbs. of trowel grade aggregate.
Physical Properties
| Volume mix ratio | 4 to 1 (Resin to Hardener) |
| Viscosity (mixed) | 300 - 500 CPS Typical |
| Solids Content (%) | 98% (ASTM D-2697) |
| VOC | 42 g/l (EPA method 24) |
| Application Temps. | 60° – 85° F |
| Hardness | 70 – 80 (Shore D) |
| Gel Time | 20 - 30 minutes @ 75° F |
| Dry to Touch (recoat with compatible products) | 4 - 5 hours @ 75° F |
| Through Cure | 8 - 12 hours @ 75° F |
| Open for light traffic | 24 hours @ 75° F |
| Shelf life | 1 year in unopened units |
Limitations & For Best Results
- Do not thin this product.
- Do not apply when humidity exceeds 70% indoors.
- Do not allow to puddle during application.
- Allow each coat to dry to tack-free or clear prior to re-coat.
- When re-coating, always apply the next coat within 24 hours of completing the previous coat.
- Mortar should be installed at a minimum 1/8" thickness.
- Do not use POXI-ROCK FLOORING as a neat coating. Always mix with aggregate and apply as mortar OR broadcast to rejection.
Product Application
Install mortar mix over wet prime coat of the same material. Finish using a steel hand or power trowel. ROCK-TRED product test data is based on environmental temperatures of 75° F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
POXI-ROCK FLOORING is manufactured in Amber/Clear and can be pigmented using ROCKTRED Universal Colorants. When pigmenting a 100 lbs. mix of POXI-ROCK FLOORING aggregate mortar use ½ BAG-PAK of Universal Colorant. Dark colors work best to color an aggregate mortar.
Chemical Resistance
Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-3 profile followed by wet priming with POXI-ROCK FLOORING liquids is the best and recommended installation method for POXI-ROCK FLOORING mortar applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.