High Performance Flexible Lht Mortar
SikaTile®-475 LHT Premium Set is a premium-grade, single-component large and heavy tile mortar that is ideal for installation of gauged (formerly “thin”) porcelain tile as well as large and heavy ceramic and porcelain tile and natural stone. This high-performance, flexible, polymer-modified mortar is formulated for ease of application and features up to 50% more coverage, extended open time and superior transfer properties to enhance back-buttering
Features
- 48 Bags per pallet
- For use with large ceramic, porcelain, gauged porcelain, marble, granite, and natural stone
- Flexible adhesive, suitable for high traffic area
- Superior transfer promotes full coverage for gauged porcelain tile panels
- May be applied up to 3/4" (19 mm) thick on horizontal applications
- Up to 50% more coverage
- For interior and exterior floors and walls
- Creamy and easy to spread
- Mold and mildew resistant
Suitable Substrates
- Ceramic Tile and Stone
- Cement Backer Board
- Cement Mortar Beds (cured)
- Cement Plaster
- Cement Terrazzo
- Concrete
- Exterior Grade Plywood (interior use only)
- Concrete Masonry
- Lightweight Gypsum Concrete (interior use only)
- SikaLevel Products
Advantages
- For use with large ceramic, porcelain, gauged porcelain, marble, granite, and natural stone
- Flexible adhesive, suitable for high traffic area
- Superior transfer promotes full coverage for gauged porcelain tile panels
- May be applied up to 3/4" (19 mm) thick on horizontal applications
- Up to 50% more coverage
- For interior and exterior floors and walls
- Creamy and easy to spread
- Longer working time
- Mold and mildew resistant
ENVIRONMENTAL INFORMATION
Sika® is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product can contribute towards LEED® v4.1 certification:
- Up to 2 points towards MR Credit 5, Regional Materials
- Up to 1 point towards IEQ Credit 4.1, Low-Emitting Materials – Adhesives & Sealants
APPROVALS / STANDARDS
American National Standards Institute (ANSI) — ANSI A108.5, A118.15TE, A118.4TE and A118.11 of the American National Standards for the Installation of Ceramic Tile ASTM International (ASTM)
- ASTM C109 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2” or 50mm Cube Specimens)
- Resilient Floor Covering Institute - (RFCI) Recommended Work Practices for Removal of Resilient Floor Coverings
- Tile Council of North America (TCNA) - TCNA Handbook for Ceramic Tile Installation, TCNA EJ171 Movement Joint Guidelines.
- ISO 13007-2 C2TES1P1
Chemical Base
Portland cement, selected aggregates, water retention additives, re-dispersible polymer
Shelf Life
12 months from date of production when stored in original, sealed package
Storage Conditions
Store in undamaged, original, sealed package, in dry conditions at 73⁰ F (23⁰ C)
4 Week Shear Bond Strength
| Property | Test Method | Requirement | Typical Results |
| Porcelain Tile | A118.15 Section 7.2.5 | > 400 psi | 550 - 650 |
| Quarry Tile to Plywood | A118.11 Section 4.1.2 | > 150 psi | 200 - 300 |
ISO 13007 Classification
| Classification Code | Classification Requirement | Results |
| C2 (cementitious, improved adhesion) | ≥ 145 psi (1 MPa) after standard aging. Heat aging, water immersion and freeze/thaw cycles | Pass |
| E (extended open time) | ≥ 72.5 psi (0.5 MPa) after 30 minutes | Pass |
| T (vertical slip resistance) | ≤ 0.02" (0.5 mm) | Pass |
| S1 (normal deformation of mortar) | ≥ 0.1" (2.5 mm) | Pass |
| P1 (normal adhesion to plywood) | ≥ 72.5 psi (0.5 MPa) | Pass |
Mixing Ratio
7.2 quarts (6.8 liters) of clean potable water per 50 lb. bag
Pot Life
4 Hours
Open Time
> 30 minutes - Passes ANSI A118.15 Section 5.3
Cure Time
Product Curing time is affected by ambient and surface temperatures and humidity. Use the following as a guideline. Allow 24-48 hours before grouting and light traffic, and 7 days before heavy or vehicular traffic. As necessary, use plywood or other load distributing protection when moving heavy equipment across tiled assembly.
MIXING
In a clean container, add approximately 7.2 quarts (6.8 liters) of clean potable water, then add the contents of the 50 lb. (22.68 kg) SikaTile®-475 LHT Premium Set. Mix thoroughly by hand or with a slow speed mixer at < 500 rpm to a smooth, thick, trowelable consistency. Allow mortar to slake for approximately 3 to 5 minutes, and then remix before using without adding additional water or powder. Mortar consistency shall be such that when applied with the recommended notched trowel to the substrate, the ridges formed in the mortar do not flow or slump. During use, stir mortar mix occasionally. Do not add additional water. Do not add latex liquid additives to SikaTile®-475 LHT Premium Set.
APPLICATION
Read all installation instructions before installation. Choose a notched trowel with sufficient depth to achieve more than 80% mortar coverage and transfer to substrate and back of tile to both the tile and substrate for all interior applications, and more than 95% for exterior, commercial floor and wet applications, back-butter the tile to meet these requirements. With pressure, apply a coat of mortar by using the flat side of the trowel to key the mortar into the substrate. With the notched side of the trowel, apply additional mortar by combing it in a single direction parallel to the shortest dimension of the tile. Spread only as much mortar as can be tiled before the product skins over. Open time can vary with jobsite conditions. Set tiles firmly into the wet mortar and push the tiles back and forth in a direction perpendicular to trowel lines to collapse the mortar ridges and to help achieve maximum coverage.
CLEANING OF TOOLS
Clean tools and tile with water before the material dries.